Vessel Electric Drum Ball

Make Nail it!! even more fun with this easy-to-use rechargeable screwdriver

"Pounding string art nails is hard because there are so many of them."
"I hammered a nail into the edge of the board and it cracked!"
The Electric Drill Ball is here to answer those concerns.
By attaching the cushion drill (sold separately ), you can drill a pilot hole that is perfect for Nail it!!, reducing the strain of hammering in the nails and reducing wood cracking.

It comes with a No. 2 Phillips bit, making it ideal for assembling furniture!
This is a driver I would recommend every household have.

Staff N...Nail it!! Skill: Beginner

The number of times each nail needs to be driven has been reduced from 4-5 times to 2 times.
The nail went in easily and was easy to hammer in.
The drill rotates slowly so it's not scary.
The switch operation may take some getting used to.

Staff E...Nail it!! Skill: Beginner

It makes it so much easier to insert nails! When I concentrate on my work I tend to lean forward, so it's really helpful to have the light brighten up the area around me.
The switch is still pressed when you remove the drill. You have to be careful not to turn it off accidentally.

Staff H... Nail it!! Skill: Intermediate

The number of times each nail is driven is reduced from 4 to 2. It is much easier than not having to drill at all.
Another benefit is that it reduces the noise of hammering nails to some extent.
If you drill too deep it will go right through the board, so I think it's very important to mark the drill beforehand.

Nail it!! using an electric drill ball - Tips for drilling holes

* A special drill is required to make holes. Please purchase separately or use our economical drill set .

1. Make a mark about 10 mm from the tip of the drill (NIJ0006)!
There is a risk that the drill will penetrate the board and damage a desk or other object.
Make a mark with tape beforehand to show how deep you want to drill the hole.

2. Drill straight!
If the hole is angled, the nail will be hammered in at an angle.
Try to keep the drill as straight as possible when drilling.
If the nail is at an angle, use pliers or a threading pen to straighten it after hammering it in.

3. Keep the switch pressed even when unplugging!
When the rotation stops, it is difficult to remove the drill from the board.
Keep the switch on from the time you start drilling until you finish removing the drill.
If you try to pull out the drill when it has stopped rotating, it may be damaged.

Product Specifications

Note

●Please be sure to read the instruction manual.
●When working with electrical equipment, be careful of short circuits and electric shocks.
●Overloading may cause damage or injury.
●Please store this product at home with caution as children may get caught out.
●Please use a charger with the specified rated output (output: 5V-1A). Chargers with a high current value will shorten the life of the built-in battery.
●When working at height, be careful not to drop bits or electric screwdrivers as this may cause an accident.
●If you use a bit other than the specified one, the bit may become stuck.
When installing or removing the bit, do not touch the switch, as this may cause the electric screwdriver to start operating and result in injury.
●Make sure to attach the bit securely. If the bit comes off during work, you may be injured.
●Do not continue to press the switch after the power has automatically turned off, as this may damage the internal components.
●Continuous overloading may result in breakdown.
●Do not look directly at the LED light as it may damage your eyes.
●Do not operate the switch when tightening by hand. Doing so may cause damage to the electric screwdriver due to overload.
●Do not use the electric screwdriver for work that exceeds the maximum manual torque stated in the instruction manual. Overloading the screwdriver may damage it.
●Before carrying out maintenance or bit replacement, or before transporting or storing the tool, make sure the switch is in the center position. Accidental switching on of the switch may result in injury.
●The cover is made of reinforced plastic. Do not wipe it with detergent or the following chemicals, as this may cause cracks, electric shock, or breakdown.
Benzine, paint thinner, ketones (acetone, etc.), ethers, and other similar chemical substances. ●When an abnormality occurs, use with caution and do not operate the switch. There is a risk of fire or electric shock.
●Never disassemble or modify the product yourself. Doing so may result in injury, malfunction, smoke, fire, or electric shock.
●Do not attempt to disassemble the battery or remove any of its components as this may result in fire or injury.

others

Although we strive to display the latest product information on the website, product specifications may change without notice due to manufacturer reasons. For this reason, the product information on the website may differ from the actual product you receive, so please be sure to check the product label and instructions before use. If you require more detailed product information, please contact the manufacturer.

Vessel Home Page

More information about Dendo Ball